When a cement particle hydrates there is a reaction between water and the cement that causes it to become a hard, solid mass. There are also chemical by-products created which lie dormant in the concrete. When we combine the by-products of cement hydration and moisture in the presence of XYPEX, a chemical reaction takes place and the product of this reaction is a very dense, insoluble, inorganic, dendritic crystalline structure.

The development of this crystalline structure can only take place where moisture is present and thus XYPEX tends to form this crystalline material in the bleed water tracts, capillary tracts and shrinkage cracks in concrete. Wherever water goes, XYPEX will form.

The waterproofing effect of XYPEX is due to two reactions: one chemical, and one physical.

When XYPEX is being used as a coating for waterproofing, or other remedial work, on existing concrete structures, in order to get the chemicals from the coating into the concrete, we rely on the physical reaction, diffusion. Diffusion occurs when chemicals in solution of high density migrate through a solution of lower density until the two equalise.

Crystals will grow up to .45 metres into the concrete from an external specified application, subject to water presence. Growth rates are approximately 50 mm for the first three weeks and 10 mm per week thereafter, depending on presence of moisture.

Since the process is catalytic, the crystalline structure can re-activate many years after the original application, to seal, or re-seal, defects which might occur in the concrete at a later time providing, cracks do not exceed 0.4 mm. It should be noted that XYPEX products are not fluid and as such may not be suitable for sealing live structural cracks on a stand alone basis.

Concrete can be treated with XYPEX by 4 methods:

1. Within the concrete, in the initial mix, using XYPEX Admix.
2. As a “Mud Slurry” of XYPEX Concentrate beneath new Concrete
3. Applied over a finished structure on the outer surfaces, at any period of the structures life, using XYPEX Concentrate and/or XYPEX Modified.
4. Applied to green concrete as a dry shake powder which is trowelled into the concrete, using XYPEX DS1.

A coating of XYPEX Concentrate and/or Modified is never waterproof in itself. The coating is only the source of XYPEX chemicals which are progressively drawn from the coating into the matrix of the concrete during the initial curing process. If required, the XYPEX coating itself may be removed after 4 to 5 weeks as the waterproofing (i.e. the crystalline growth) is deep into the concrete by this time.

• XYPEX does not require dry weather, costly surface priming or leveling prior to application.
• XYPEX does not require a dry surface, in fact, a wet surface is necessary.
• XYPEX cannot puncture, tear, rupture or come apart at the seams.
• XYPEX does not restrict site access or require protection during back filling, placement of steel, wire mesh or other materials.
• XYPEX does not require costly sealing, lapping and finishing of seams at corners, edges or between membranes.
• XYPEX is cheaper to purchase and apply than most membrane applications.
• XYPEX waterproofs and protects the whole of the structure, not just the surface.

• Yes, self healing capacity for cracking up to approximately 0.4mm in width.
• Yes, corrosion protection
• Yes, neutralised chloride ion activity.
• Yes, chemical resistance.
• Yes, reduced carbonation
• Yes, prevention of alkali aggregate reaction.
• Yes, gains in concrete design strength.
• Yes, reduced water cement ratios.
• Yes, accelerated early and ultimate strength.

A XYPEX application, unlike most other systems, is permanently reactive to the presence of water. The fibrous crystalline growth, due to its unique composition, will not deteriorate under normal conditions.

When applied in accordance with the Specifications, XYPEX functions at 100% efficiency within the following conditions:

pH Range                                -3.00 to 11.0, in constant contact.
                                                   – 2.0 to 12.0, in periodic contact.
Temperature Range               -+ 130C to -32C constan
                                                    – +1530C to -185C periodic
Humidity                                  -No effect
Ultraviolet                                – No effect
Oxygen Level (Oxidisation)  – No effect

XYPEX is approved for use on structures that contain potable water or foodstuffs by many agencies, including:

• NSF 61 “Drinking Water System Component – Health Effects”, NSF International, Ann Arbor, Michigan
• Drinking Water Inspectorate – DWI – (UK Authority responsible for product approval re potable water), London, England
• Sirim Malaysia [98 KL0427]
• Singapore Institute of Standards and Industrial Research
• Japan Food Research Laboratories (Water Quality Test according to Tap Water Act) Tokyo, Japan
• Australian Water Quality Centre (Authority for approval of all products in contact with potable water) Bolivar, South Australia
• State Health Institute & Center For Drinking Water, State Health Institute,
  (Prague, Czech Republic)
• Federal Department of Health, Division of Chemicals
  (Berne, Switzerland)
• National Institute of Occupational Health, Register of Substances and Materials (Copenhagen, Denmark)
• Mairie De Paris, Research Center for the Control of Water,
  (Paris, France)